| Model | KUS-35-5 | KUS-35-12 | KUS-35-15 | KUS-35-24 | KUS-35-36 | KUS-35-48 |
| output | DC voltage | 5V | 12V | 15V | 24V | 36V | 48V |
| Rated current | 7A | 3A | 2.4A | 1.5A | 1A | 0.8A |
| Current range | 0~7A | 0~3A | 0~2.4A | 0~1.5A | 0~1A | 0~0.8A |
| Rated power | 35W | 36W | 36W | 36W | 36W | 38.4W |
| Ripple&noise | 100mVp-p | 120mVp-p | 120mVp-p | 150mVp-p | 200mVp-p | 200mVp-p |
| DC voltage ADJ. range | ±10% | ±10% | ±10% | ±10% | ±10% | ±10% |
| Voltage toleranceNote.3 | ±3% | ±2% | ±1% | ±1% | ±1% | ±1% |
| Line regulationNote.4 | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% |
| Load regulationNote.5 | ±2% | ±1% | ±0.5% | ±0.5% | ±0.5% | ±0.5% |
| Setup,rise,hold up time | 800ms,30ms,30ms/230VAC(full load) |
| input | Voltage range | 90~264VAC，127～373VDC |
| Frequency range | 47~63HZ |
| AC current | 0.7A/115VAC 0.42A/230VAC |
| Inrush current | Cold start 45A/230VAC |
| Efficiency | 83% | 86% | 87% | 88% | 89% | 90% |
| Leakage current | <0.75mA/240VAC |
| protection | overload | Rated output power110%~150% start over load protection |
| protection type:hiccup mode，auto-recovery after fault condition is removed |
| Over voltage | Rated output voltage 115%~135% Start over voltage protection |
| Protection type：hiccup mode，auto-recovery after fault condition is removed |
| environment | Working temp,humidity | -30℃～+70℃(Please refer to“derating curve”) |
| 20%~90%RH Non-condensing |
| Storage temp,humidity | -40℃~+85℃，10%~95%RH non-condensing |
| Withstand vibration | 10~500HZ，2G10min/1cycle，period for 60 minutes，each axes |
| safety | Withstand voltage | I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC |
| Isolation resistance | I/P-O/P,I/P-FG,O/P-FG:100Mohms/500VDC |
| Fit standard | Safety standards | Compliance to UL60950-1,TUV EN60950-1,GB4943 |
| EMC emission | Compliance to EN55022(CISPR22)Class B，GB9254 Class B,EN55014,EN61000-3-2,3 |
| EMC immunity | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61000-6-1 |
| others | Dimension | 99*82*30mm（L*W*H） |
| Weight/packing | 0.23kg/60pcs/14.8kg/0.025m³/0.88CUFT |
| MTBF | ≥720K hrs min. MIL-HDBK-217F(25℃) |
| note | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃of ambient temperature. |
| 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. |
| 3. Tolerance : includes set up tolerance, line regulation and load regulation. |
| 4.Line regulation is measured from low line to high line at rated load. |
| 5.Load regulation is measured from 0% to 100% rated load |
| 6.The ambient temperature derating of 5℃/1000 m is needed for operating altitude greater than 2000m(6500ft) |
| 7.The power supply is considered as a component which will be installed into a finalequipment.The final equipment must be re-confirmed that it still meets EMC directives.For guidance on how to perform these EMC tests. |
keweisales
LIVE CHAT
